s45c vs ss41

S45C (Japan, JIS ) European (EU, EN) and wordwide Steel equivalent grades These comparison table is only intended as an indication of the closest khown equivalent grades. The source standarts should always be checked for the specific purpose for each material, in case of doubt Buy, sell, suppliers search product S45C on line

S45C steel grade is a very common engineering steel materials. In this post, you can check the thorough technical and properties of machine structural S45C carbon steel. 1. S45C Steels belongs to JIS G4051 S45C Steel Grade is one steel grade material in JIS G4051.

Jul 20, 2017 · Differences between S45C and C45S45C* S45C is a medium strength steel. Suitable for shafts studs, keys etc. Available as rolled or normalised. Supplied as square bar, or round bar or flat. They are excelling in weldability & machinability , an

G3101 SS41 steel is a kind of material for boiler and pressure vessel steel.So, G3101 SS41 steel is used above all for manufacturing boilers, pressure vessels and pipes transporting hot liquids. About G3101 SS41 steel, we can offer SS41 steel plate specifications according to your requirements.

Steel plate Material comparision GB JIS ASTM Q235 F SS41 G3101 A36 USt37 2 1.0112 DIN17100 Q235 SS41 G3101 A283 C RSt37 2 1.0114 DIN17100 Q255A SS50 G3101 A283 D (RSt42 2) 1.0134 DIN17100 (A3R) SPV24 G3115 A285 C 20g SB42 G3103 A515.Cr60 H 1.0425 DIN17155 (15g) SB35 G3103 A515.Cr55 H 1.0345 DIN17155

SAE AISI 1045 (S45C, G10450) Carbon Steel. SAE AISI 1045 steel is a carbon (non alloy) steel formulated for primary forming into wrought products. 1045 is the designation in both the SAE and AISI systems for this material. G10450 is the UNS number.

European equivalent grade for Non alloy quality structural steel SS400 (JIS )S275JR (1.0044) Cross reference table for Steel SS400 (JIS ) and its European equivalent S235JR (1.0038(dubl)) ( EN )

SS41 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc. Join Supplier[email protected]

2867 2868 FC 37 1 [Materials Data] Comparisons of Materials between JIS and Foreign Standards 2 Steel Brands Comparative Table/Hardness of Materials and Corresponding Tools

Both ASTM A36 carbon steel and SAE AISI 1045 steel are iron alloys. They have a very high 99% of their average alloy composition in common. There are 31 material properties with values for both materials.

offers 1,775 ss400 s45c steel products. About 52% of these are steel round bars, 29% are steel sheets, and 2% are steel pipes. A wide variety of ss400 s45c steel options are available to you, such as aisi, astm, and gb.

S45C is a medium strength steel. Suitable for shafts studs, keys etc. Available as rolled or normalised. Supplied as square bar, or round bar or flat. They are excelling in weldability & machinability , and they can be subjected to various heat treatments. Based on JIS G 4051 2009. S45C Mechanical Properties. Density (kg/m3) 7700 8030

Carbon steels (such as S15C, S45C, S50C, S55C, and S60C) have lower carbon content than carbon tool steels (SK), and are used in applications that require a certain amount of strength and toughness. Carbon steels with low carbon content offer better raw material workability, but are susceptible to uneven quenching, so care must be taken with regard to temperature management, cooling methods

Tool & Die Steels Inc. Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. S45C Round Bar S45C Flat Bar S45C Hollow Bar S45C Tube / Pipe S45C Sheet / Plate S45C Strip / Coil S45C Wire S45C Forging S45C Tube / Pipe TEL:+86 13880247006

According to Material Grades, SS400 steel is defined in JIS G 3101 standard, which is a Japanese material standard for general structural usage, sheets, strips and rolled steel plates. They are also

[Materials] Standard Material Sizes 2 [Materials Data] Comparisons of Materials between JIS and Foreign Standards 1 Q Carbon Steel for Machine Structural Use, Alloy SteelStainless Steel Materials Type Material Code Shapes Unit Standard Dimensions

Steel Grade Equivalent Table (EN, SAE/AISI, UNS, DIN, BS, UNI, JIS) The table below compares common grades of materials from various international specifications. Note that materials compared are the nearest available grade and may have slight variations in actual chemistry.

JIS G3101 SS41 with JIS G3101 SS400) U Khin Thein. Reply. Dear Sir,I would like to enquiry for M.S Plate And Angle Iron specification for ss400 steel grade jis g3101 required qtty.(5) items for our client MOGE Ref.no.DMP/L 096(17 18).I will send details specification sheet after contact received.Best Regards,Khin Thein.

SS400 is one of the most commonly used hot rolled general structural steel.SS400 steel plate, JIS3101 SS400 steel plate, under JIS3101 standard, we can regard SS400 steel plate as Carbon and low alloy steel SS400 steel plate is one mainly of Carbon and low alloy steel, SS400 steel plate would be used to built containers which can bear low temperature sea water.

Steel bar an wire elements Standard No. Standard name Symbol Primary usage G 3101 Rolled steel material for general structure SS Bolts, nuts and pins G 4051 Carbon steel material s for machin e structure S C Nuts , boltsshaft a nd automobil compo ents G 3108 General steel materials for cold nished steel bar SGD Nuts, shafts and automobile

S50C is also a common steel grade with wide application. Its similar to S45C carbon steel, no matter in properties or in applications. But customers in different area will have different habit for S45C or S50C. Besides, the cost and price for both S45C and S50C steels are just little different.

ss400,s45c,s50c,sncm439,scm439,skd11,skd61,scm440,scm4,skh51,sk5,aud11,,,

S45C JIS G 4051 (Japan) Standards JIS G 4051 Carbon steels for machine structural use Chemical composition C 0.42 0.48 Si 0.15 0.35 Mn 0.6 0.9 P < 0.03 S < 0.035 Cr < 0.2 Ni < 0.2 Cu < 0.3 Fe Rest Ni + Cr < 0.35 Properties By JIS G 4051

TECHNICAL DATA» COMPARISON OF MATERIALS BETWEEN JIS AND FOREIGN STANDARDS(1) Japan Industrial Standards Steel Types Related to Foreign Standards Standard Number Code Name Chrome molybdenum Nickel chrome steel Nickel chrome Chrome steel steel National standard of the former USSR Stainless steels C Heat resisting steels and related materials